By Plumbing Guide for Installing a Bathtub
By Plumbing Guide for Installing a Bathtub
Blog Article
They are making several great points related to A Step-by-Step Guide to Installing a Bathtub as a whole in the content directly below.
Installing a tub isn't specifically brain surgery, however it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a new one is likewise a moderately difficult project. If the old tub is readily easily accessible, the job can relocate quickly; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old tub as well as set in the brand-new one. Make sure you have qualified on your own for the job and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to think about utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This article will help you mount a new tub in your shower room if you have actually already acquired a new tub as well as do not require to change the plan of your previous water pipes.
Your tools and also material checklist ought to make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic because of the limited gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin ensuring that the washing machines are in location in between the faucet as well as the sink. Protect the tap in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Utilizing the two wooden boards under its feet, put the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub till the level reviews level.
To mount faucets, fit the bottom of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Switch on the supply of water as well as check all joints as well as brand-new pipework for leakages and tighten them if required. Load the tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the tub needs to wait up until the bath tub has been made use of a minimum of once as this will certainly settle it into its final setting.
Getting ready for the Setup
First of all, the sustaining framework provided with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent stress on the tub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, triggering the water to penetrate the wall surface between the bath and the tiling, causing complications with moisture as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can split fairly early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on Installing A Bathtub? Put feedback directly below. We would be interested to hear your responses about this blog entry. In hopes that you come back again in the future. If you enjoyed reading our blog entry plz remember to share it. I am grateful for your time. Come back soon.
Leak detection needed? Report this page